Cart - 0 Item
You have no items in your shopping cart.
You have no items to compare.
- Category
-
- Spools, casting reels (82)
- Handles, casting reels (73)
- Handle knobs (67)
- Gears, brakes, level winders (83)
- Ball bearings, Pin remover (9)
- Spools, spinning reels (32)
- Handles, spinning reels (13)
- Frames, plates, star drag, colored parts (39)
- Drag washers (30)
Tuning Parts
-
Avail ABU Mechanical Brake Knob 55ST
ABU Ambassadeur 1000C-7500C, later than 1980 year models, except 1500C, 2500C, 3500C. Light weight 1.1g, machined ESD(extra strong duralumin, air craft grade duralumin) mechanical brake knobs. Doesn't come with copper washers inside.
-
Avail ABU Mechanical Brake Knob 2500C
ABU Ambassadeur 1500C, 1600C, 2500C, 2600C, 3500C. Light weight 1.1g, machined ESD(extra strong duralumin, air craft grade duralumin) mechanical brake knobs. Doesn't come with copper washers inside. Not fitting to 1500CA limited, 3500CA limited.
-
Avail Nezumigashi 7000, line falling stopper for ABU 7000
This plastic plate kit prevents lines falling between spool and frame for ABU Ambassadeur 7000/7001, 7500/7501. Not fitting to 7000i instant-anti-reverse models. For some old 7000, pinion gear top might contact to the thin part of the gear side plate, and please cut out the part.
-
Avail ESD Main Gear Shaft 1500C, 2500C, IAR
Ultra light main gear shaft of ABU 1500C, 2500C made of extra strong duralumin (ESD), to remove 8g weight from the part. Fits to all ABU 1500C, 2500C, 3500C reels with IAR, instant-anti-reverse. Not fit to 1600C or 2600C thumb bar clutch models. 3.2g. Genuine brass shaft 10.2g. Clutch return posts are increased from 2 to 4, and you may return clutch faster.
$36.00 -
DRT Varial custom handle 110mm flat knob (without center nut) Limited offer
DRT Varial handle is full machined heavy duty handles for big baits. This 110mm version has large DRT flat knobs. Handle plate is quite thick 6mm at center to offer SOLID cranking. Stiff rubber knobs are large enough to grip firmly. Accept straight star up to 27mm radius, and sway back star drags. DRT Handle center nut is not included, and please purchase at least one or you may not fit the handle to reels. You may fit DRT flat knobs to this handle. Comes with fitting plates in 7mm and 8mm, wrench for center nut. Made in Japan
-
Livre handle nuts
These are the center nuts for Livre handles. Please specify 7mm/8mm shaft size, Right/Left handle, and color. 7mm fits to 50-250 Shimano bait casters. 8mm fits to Daiwa/ABU and Shimano Conquest 300/400 models. Daiwa B1 SCR fits to Daiwa with hex head scenter crews, for example Steez, Zillion TW, Tatula HD, Ryoga, Z2020. These nuts also fit to DRT handles. CBF nuts are machined more to remove weight.
-
Shimano 13/16Metanium micro-module brass gear kit
This is the brass gear kit for 13Metanium, 15Metanium DC and 16Metanium MGL reels. Gears are micro-module brass gears from Shimano. Stock main gears of these models are made of duralumin, which is not as durable as brass. You may change gear ratio to any of 6.2, 7.4 and 8.5. Comes with drive gear, pinion gear and a carbon drag washer. Drive gears and washers are from Shimano 19 Scorpion MGL. Pinion is that of Shimano 16 Metanium.
-
Avail aluminum alloy worm shaft 2500C
This is the compatible level winder worm shaft of ABU 2500C, made by aluminum alloy to remove weight. Fits to 2500C, 2501C, 2600C, 2601C, 3500C. 2.3g (genuine worm shaft 6.1g) Plastic part is made of Duracon POM to offer friction-less operation.
$36.00 -
Avail Microcast Spool ALD0928R II for Shimano 09 Aldebaran MG, Core 50MG Re-stocked!
09Aldebaran Mg/Mg7, 10Scorpion XT1000/1001, 09Core 50MG, 10Chronarch 50E, 10Curado 50E. 4pt brake holder installed. Casts great for heavier than 3.0g 1/8oz. 0.26mm-50m/55yds 7.2g
-
Avail Microcast spools CNQ5020TR 00Conquest 50/51
Shimano Calcutta 00Conquest 50/51(year 2000-2013 model) 4 pt brake holder installed. Work with Magnet brake Avail SHSC-50A as well. Casts great for heavier than 2g. 0.205mm-45m/50yds 7.0g
-
Shimano 20 Metanium Japan spool
Genuine spool of Japan version 20 Metanium, 20% shallower spool than export version 20 Metanium, to improve casting performance for light rigs. It holds 0.285mm(US10lb)-100m(110yds), instead of export spool of US12lb(0.30mm)-110yds(100m). Spool depth 7mm at 2mm from side edge, instead of 9mm of export. Comes with brake holder and 4 brake blocks installed. Ready to use. Fits only to 20 Metanium reels. 14.1g
$79.00 -
Mike's Reel Repair Ball bearing Speed bushing 20639
Ball bearing supported spool bushing, compatible to 20639, to remove friction from spool spin. Ball bearing inner race supports spool cog side, while it is floating from spool shaft. With this bearing bushing, you may not much tighten the spool tension by cap, as bearing works against. Therefore, this is only recommended when you want to reduce minimal amount of friction from spool spin, and it is recommended to cast heavy rigs the longest. ABU4500CS, 5500CS, 6500C, 6500CS and etc, with 20639 brass bushing.
$13.00 -
Mike's Reel Repair Dual ball bearing worm kit
2 Ball bearing installed level winder kit removes friction and add casting distance.Three models, 4000, 5000, 6000 available for ABU Ambassadeur 4000-4600, 5000-5600, 6000-6600 respectively.
-
Shimano Yumeya 20 Metanium Shallow spool 20 Metanium
Shimano 20/22/23 Metanium reels
Light weight 14.3g, 35% shallower spool than Japan version 20 Metanium stock spool, 50% shallower than export Metanium (24 Metanium 100), to improve casting performance for light rigs around 3/16-1/2oz. 0.285mm(US10lb)-65m(70yds). SVS Infinity brake installed. You may cast from 5.0g with this spool without effort.$104.00 -
Daiwa SLPW EX LT 3000S Black spool d
Machined aluminum spool, with CRBB ball bearing added inside for smooth drag. ATD drag system. Daiwa 18/22 Exist, 19 Certate, 21 Luvias Airity, 23Airity (LT3000, PCLT3000, 3000C) Line capacity 8lb(0.23mm)-100m(110yds), 6lb(0.20mm)-150m(165y), 30g, 10kg drag
Regular Price: $96.00
Special Price $67.00
-
Daiwa SLPW EX LT 3000 Black spool d
Machined aluminum spool, with CRBB ball bearing added inside for smooth drag. ATD drag system. Daiwa 18/22 Exist, 19 Certate, 21 Luvias Airity, 23Airity (LT3000, 3000C) Line capacity 12lb(0.285mm)-100m(110yds), 8lb(0.235mm)-150m(165y), 30g, 10kg drag
Regular Price: $96.00
Special Price $67.00
-
Daiwa SLPW Machine-cut handle Black 50mm
Solid machine-cut handle. Fits to Daiwa reels with no hex handle shaft, Exist, Steez, Certate, Bradia, Luvias, Fuego and etc 1000-2500 size. Comes with 2 CRBB 4x7x2.5 ball bearings and washers. Fits with Daiwa S knobs.
$68.00 -
Daiwa SLPW Machine-cut handle Black 55mm
Solid machine-cut handle. Fits to Daiwa reels with no hex handle shaft, Exist, Steez, Certate, Bradia, Luvias, Fuego and etc 1000-3000, LT2500-5000C. Comes with 2 CRBB 4x7x2.5 ball bearings and washers. Fits with Daiwa S knobs.
$68.00 -
Daiwa SLPW Machine-cut handle Black 60mm
Solid machine-cut handle. Fits to Daiwa reels with no hex handle shaft, Exist, Steez, Certate, Bradia, Luvias, Fuego and etc 2500-3000, LT3000-5000C. Comes with 2 CRBB 4x7x2.5 ball bearings and washers. Fits with Daiwa S knobs.
$68.00 -
Daiwa SLPW Machine-cut handle Black 65mm
Solid machine-cut handle. Fits to Daiwa reels with no hex handle shaft, Exist, Steez, Certate, Bradia, Luvias, Fuego and etc 3500-4000, LT5000-6000. Comes with 2 CRBB 4x7x2.5 ball bearings and washers. Fits with Daiwa S knobs.
$68.00 -
Itocraft Mountain Custom CX kit for Cardinal 3 Limited offered!
This is the tuning kit for Cardinal 3 and 33 to remove weight by 20g. It includes following. #1 machined side plate #2 side plate screw #3 spacer #4 bail mount screw #5 bail arm screw #6, 7 drive gear shaft sleeve #8 nut #9 protecting ring
-->$139.00 -
Avail aluminum alloy 2BB worm shaft 2500C
This is the 2 ball bearing installed compatible level winder worm shaft of ABU 2500C, made by aluminum alloy to remove weight. Fits to 2500C, 2501C, 2600C, 2601C, 3500C. 3.0g (genuine worm shaft 6.1g) Ball bearings removes friction in roration drastically. Plastic part is made of Duracon POM to offer friction-less operation.
$56.00 -
Valleyhill Classic Power Handle ST I shape 80mm Selling out sale 50% off, was sold for $39
80mm chrome straight frame handle. Knobs are in transparent colors. Matches quite well with classic ABUs. Fits to ABU bait casters 1500-6600. Comes with retainer, nut (R) and screw. No ball bearing installed
-
Valleyhill Classic Power Handle ST 80mm S-shape plain (no hole) frame Selling out sale 50% off, was sold for $39
80mm chrome, plain frame handle without holes. Knobs are in transparent colors. Matches quite well with classic ABUs. Fits to ABU bait casters 1500-6600. Comes with retainer, nut (R) and screw. No ball bearing installed
